Unicyclist Community

Go Back   Unicyclist Community > Unicycling Discussion > Unicycling Articles and Tutorials

Reply
 
Thread Tools Search this Thread Rate Thread Display Modes
Old 2017-11-19, 10:12 AM   #16
UniMyra
I don't like unicycling, I love it.
 
UniMyra's Avatar
 
Join Date: Aug 2011
Location: Oslo (Kolbotn), Norway
Age: 53
Posts: 580
Quote:
Originally Posted by Jener8or View Post
I don't think the Dominator2 rims have any eyelet offset or angled drilling.
You're probably right. I've e-mailed UDC to make sure.

Quote:
Originally Posted by Jener8or View Post
What I try to pay attention to is on a USED hub, try to match the previous lacing pattern, so it doesn't create any more wear marks from the spokes. As long as you can see the hub label in the valve hole, you'll be just fine.
I wasn't aware of this. I started with a random spokehole on the hub.

Quote:
Originally Posted by Jener8or View Post
Where you have to take it into account is in spoke length. Some spoke calculators don't account for offset or asymmetrical spoke beds, so you need to find out if your math or your resource does and adjust spoke length accordingly.
I use the UDC spoke calculator and went up to the nearest mm. That seems to be the correct length for the way I laced the wheel.

Quote:
Originally Posted by Jener8or View Post
If the wheel has a label, you should be able to read it from the drive side.
There's a print that says "Nimbus unicycles" which I put on the left side

Quote:
Originally Posted by Jener8or View Post
As long as you can get to the valve stem, have fairly even spoke tension, and can look down through the rim at the spoke nipples and see that the spokes are all in the bottom of the nipple (or they will break) and not too long (you can get away with this on a double walled wheel or a single wall with a dremel tool
I think got this right. The spokes are not quite in the bottom of the nipples, but almost.


The video was a little bit hard to follow without a wheel to build. I will get more infomation on lacing before my next build. I will leave this wheel as it is since no one has adviced me not to.
__________________
UniMyra's YouTube channel
UniMyra is offline   Reply With Quote
Old 2017-11-19, 11:14 AM   #17
UniDreamerFR
Unicyclist
 
UniDreamerFR's Avatar
 
Join Date: Nov 2015
Location: France, near Paris
Age: 44
Posts: 499
I'm not sur about the nimbus dominator 2 rim (I don't have it by my side right now but can take a look at it tomorrow), I rather believe it has an offset (barely noticeable but still there).
I mean you have a right-handed rim or a left-handed one and you have to take it in account to know if the key spoke will be the one just after the valve hole or if you have to put it a hole away from the valve hole(sheldon guide).
Also the right flange must be connected to the rim holes of the right side.



About the schlumpf hub, if you have a first generation hub, the flange holes are alternatively filed on one side only, so they are meant to have the spoke going through it from the inside or the outside, if you don't respect this you can brake it, but I don't remember if you have a recent hub or not.
__________________
- Geared kh36 + Nightrider Lite + Kh Tbar + HS33
- Qu-ax 36" + nightrider +Q-handle+ cable rim brake
- kh 29" + knard 29x3+ kh Tbar + HS33
- Qu-ax trial 19"
-24"&26" wheels and forks and spare stuffs.
UniDreamerFR is offline   Reply With Quote
Old 2017-11-19, 06:41 PM   #18
Jener8or
Unicyclist
 
Jener8or's Avatar
 
Join Date: Oct 2017
Location: Idaho, USA
Posts: 70
I looked at my Dominator2 rim, and I would lace it as posted and the illustration showed earlier (key spoke is a trailing spoke, left of the valve stem, coming from the 4th hole from center of the hub flange). As said earlier, there are other ways to lace them that will probably not have any harmful repercussions. Searching around the forum, there is this thread, and I think the method is different ("key" spoke is a leading spoke?) but it sounds like it has proven successful as well.
http://www.unicyclist.com/forums/sho...+wheelbuilding

My stock Dominator2 rim also has one side pulling spokes going one way and the other going the other way, (it doesn't have disc brakes) just for information.

Last edited by Jener8or; 2017-11-19 at 06:44 PM.
Jener8or is offline   Reply With Quote
Old 2017-11-20, 08:33 AM   #19
UniMyra
I don't like unicycling, I love it.
 
UniMyra's Avatar
 
Join Date: Aug 2011
Location: Oslo (Kolbotn), Norway
Age: 53
Posts: 580
I've managed to get 2 parallel discussions going. I' ll try to keep the Schlumpf related questions in the Schlumpf thread.

I got an answer from Roger about the Dominator2 rim:

"The holes are drilled centrally, although if you look carefully you can see they are slightly angled when drilled. This is due to the jig type, not a requirement to build that way. The rims then have eyelets set in them at 90 degrees... so the nipples have a good seating. In my experience there is no different is built one way or the others on these rims - do not worry at all."
__________________
UniMyra's YouTube channel
UniMyra is offline   Reply With Quote
Old 2017-11-23, 10:31 AM   #20
Jener8or
Unicyclist
 
Jener8or's Avatar
 
Join Date: Oct 2017
Location: Idaho, USA
Posts: 70
Quote:
Originally Posted by UniMyra View Post
I got an answer from Roger about the Dominator2 rim:

"The holes are drilled centrally, although if you look carefully you can see they are slightly angled when drilled. This is due to the jig type, not a requirement to build that way. The rims then have eyelets set in them at 90 degrees... so the nipples have a good seating. In my experience there is no different is built one way or the others on these rims - do not worry at all."
Awesome! Roger always seems super helpful. If you haven't checked out the video of him building the penny farthing wheel, it's pretty neat. https://www.youtube.com/watch?v=3EkO4KhG-h0

Quote:
Originally Posted by Jener8or View Post
My stock Dominator2 rim also has one side pulling spokes going one way and the other going the other way, (it doesn't have disc brakes) just for information.
Re-reading this, I realize I worded this poorly (pulling/trailing spokes going the "other way" would not be pulling, of course they would be leading/pushing,) but hopefully you got that it was laced different on both sides despite me botching the explanation of it.
Jener8or is offline   Reply With Quote
Old 2017-12-24, 11:50 AM   #21
UniMyra
I don't like unicycling, I love it.
 
UniMyra's Avatar
 
Join Date: Aug 2011
Location: Oslo (Kolbotn), Norway
Age: 53
Posts: 580
I've built my third wheel with an old KH 26 Freeride rim and a Nimbus Drift Trike Disc hub.

Once again finding the right spoke lengths was a problem. I noticed that the UDC spoke calculator and the KH website stated differnt "Effective Rim Dimension" (ERD) - KH: 541 and UDC: 536. I thought I'better meassure myself and did 2 diagonal meassures which both read 545, so I went with that. The result was too long spokes. On the second try, I used the KH ERD when calculating spoke lengths. That worked well, but the spokes went all the way into the bottom of the nipples, so even the UDC ERD would have worked. Spoke lengths disc side was: UDC: 254.3, KH: 256.39, mine: 258.39.

Quote:
Originally Posted by UniMyra View Post
Nipples has to be ordered separately even though they are in the same photo as the spokes.
Not true!

This time I did some reading after all, and after building a couple of wheels the Sheldon Brown tutorial was easy reading so I followed that. The first time I got dizzy just looking at all the colored spokes, but his explanations really are excellent. Even though it was my third build, I still I managed to get the lacing wrong. I started all over and on the second try I got it right. I supect I did something wrong with the second group of spokes on the first attempt. Note to self: make sure you have enough time available when you lace a wheel.

This time I used a spoke tension meter. Lesson learned from Sheldon Brown: It is the spoke tension on the disc side that matters. The only thing to consider on the none disc side is that the spoke tension should be even. The rim is an old muni rim which has taken some beating, and it was impossible to get it true. It is off both lateral av vertical, but I did the best I could with it.

I had to grind a millimeter or so off the inside of the bearing holder/D-brake to get enough clearence for the rotor bolts.
Attached Images
 
__________________
UniMyra's YouTube channel
UniMyra is offline   Reply With Quote
Old 2017-12-24, 05:25 PM   #22
jtrops
Unicyclist
 
Join Date: May 2008
Location: Longmont, Colorado
Age: 50
Posts: 2,282
So, really you've built 4 wheels now (you just have 3 to show for it ).

On ERD:
It can be hard to get a good ERD measurement on a used rim that is as wonky as you describe. The way I measure ERD averages the entire rim in one go, so you don't need to measure in multiple places. I haven't ever had to re-order spokes.

Basically I measure the circumference of the rim at the outer edge. Then I divide by PI, to get the diameter. Then I use a depth gauge to measure the relief from the outer edge of the rim to the bottom of the nipple slot (I put a nipple like the one I'm building with in the rim to get the best reading). Then I subtract twice this relief number from the overall diameter to get the ERD. It only takes a couple of minutes and has proven to give consistently reliable results.
__________________
"A properly ridden unicycle is like an object in orbit: constantly falling but never landing." -Diogenes
jtrops is offline   Reply With Quote
Old 2017-12-25, 12:07 AM   #23
Jener8or
Unicyclist
 
Jener8or's Avatar
 
Join Date: Oct 2017
Location: Idaho, USA
Posts: 70
Quote:
Originally Posted by jtrops View Post
[...]
On ERD:
It can be hard to get a good ERD measurement on a used rim that is as wonky as you describe. The way
Basically I measure the circumference of the rim at the outer edge. Then I divide by PI, to get the diameter. Then I use a depth gauge to measure the relief from the outer edge of the rim to the bottom of the nipple slot (I put a nipple like the one I'm building with in the rim to get the best reading). Then I subtract twice this relief number from the overall diameter to get the ERD. It only takes a couple of minutes and has proven to give consistently reliable results.
Do you use a soft tape measure for getting the outer rim diameter? We have the DT Swiss spoke measuring kit, it's nice, but it's not really necessary. You can use two spokes with known lengths directly opposite each other to measure ERD, like it's shown here:
Jener8or is offline   Reply With Quote
Old 2017-12-25, 03:36 AM   #24
jtrops
Unicyclist
 
Join Date: May 2008
Location: Longmont, Colorado
Age: 50
Posts: 2,282
I use a flat metal tape. I recently got a "Pi tape" that reads with the diameter when you measure the circumference, so it eliminates one step.

I have used a few methods for measuring ERD. The opposing spokes is good (like poor mans Wheelsmith ERD rods), but it requires at least a few independent measurements to be averaged (especially with a used rim). By measuring the circumference you get an automatic average of the entire rim.

Sutherlands used to sell an ERD measuring kit that works a lot like what I'm using. The one difference was a very nice wide plastic strap that will go across the width of any rim. I have very small clips that I use when I have a difficult rim. They just hold the tape in place so it doesn't flop off the edge.

The Pi tape would be nicer if it was metric, but it's not a big deal to convert from inches to mm's. Maybe someday I'll find a metric version though.

I'll see if I can shoot some pix of my tools/process.
__________________
"A properly ridden unicycle is like an object in orbit: constantly falling but never landing." -Diogenes
jtrops is offline   Reply With Quote
Old 2017-12-25, 10:48 AM   #25
UniMyra
I don't like unicycling, I love it.
 
UniMyra's Avatar
 
Join Date: Aug 2011
Location: Oslo (Kolbotn), Norway
Age: 53
Posts: 580
I tried to meassure like in Jener8or's photo, but I must have screwed up somehow. I don't have that meassuring device either.
__________________
UniMyra's YouTube channel
UniMyra is offline   Reply With Quote
Old 2017-12-25, 01:58 PM   #26
jtrops
Unicyclist
 
Join Date: May 2008
Location: Longmont, Colorado
Age: 50
Posts: 2,282
Quote:
Originally Posted by UniMyra View Post
I tried to meassure like in Jener8or's photo, but I must have screwed up somehow. I don't have that meassuring device either.
I'm curious about how you did it without calipers.

The photo illustrates one of the biggest flaws in that system. If you look at it you can see that the spokes aren't in the diameter, but off by one hole. It's certainly not a big problem because it's easy enough to be more careful; however, it does add time.

For a personal wheel it could take as long as you want, and there would be no problem. I build wheels professionally, and when I charge $35 to build a wheel it needs to be done quickly, or I'm losing money. Systems that are fast, reliable, and accurate are essential.
__________________
"A properly ridden unicycle is like an object in orbit: constantly falling but never landing." -Diogenes
jtrops is offline   Reply With Quote
Old 2017-12-25, 03:46 PM   #27
UniMyra
I don't like unicycling, I love it.
 
UniMyra's Avatar
 
Join Date: Aug 2011
Location: Oslo (Kolbotn), Norway
Age: 53
Posts: 580
Quote:
Originally Posted by jtrops View Post
I'm curious about how you did it without calipers.
I used a ruler. Probably not the best way.
__________________
UniMyra's YouTube channel
UniMyra is offline   Reply With Quote
Old 2017-12-29, 10:46 PM   #28
jtrops
Unicyclist
 
Join Date: May 2008
Location: Longmont, Colorado
Age: 50
Posts: 2,282
Pix of my ERD process

It took a few days before I could get some pix.

The first two shots are of the diameter reading with the Pi Tape. With the rim on the glass table top I can lay the tape around the rim tightly without having to work very hard at keeping it from dropping into the well of the rim. Some disc rims don't work well with the table top, and so I have some clips that hold the tape along the edge. It works just as well, but using the table top is much faster if the rim plays along.

It reads 24 15/16", which is 610mm's.

The third and fourth photos show my depth gauge taking a reading from the outside of the rim to the bottom of the nipple slot. In this case I'm using an aluminum DT nipple, and the reading is 20.5mm's. You need to subtract twice this number from the outside diameter to get the ERD.

610-41=569mm's, and that's the ERD.

This system averages the diameter of the entire rim, and takes into account how the nipples you are building with sit in the rim.

The last photo is the tools:
1. Depth Gauge, this is a generic one that was $7, and it reads about .2 of a mm short, but otherwise it is good.
2. Stanley 33-115 PowerLock diameter tape (1/4"x10'), I bought this at a local hardware store for $8. I have found a metric one that is only about $10. I may pick one up just to eliminate the conversion.
Attached Images
     
__________________
"A properly ridden unicycle is like an object in orbit: constantly falling but never landing." -Diogenes
jtrops is offline   Reply With Quote
Old 2018-07-15, 11:12 AM   #29
UniMyra
I don't like unicycling, I love it.
 
UniMyra's Avatar
 
Join Date: Aug 2011
Location: Oslo (Kolbotn), Norway
Age: 53
Posts: 580
Should I get new spokes?

A flange on my hub broke for the second time since 2010. The last time the wheel was rebuilt by my LBS, and they reused the spokes. This time I'm going to rebuild the wheel myself. I've had to replace a couple of spokes since the wheel was new. I will use a steel Nimbus hub which according to the spokes calculator requires the same length spokes. Shold I get new spokes, or will the old ones be ok?
Attached Images
 
__________________
UniMyra's YouTube channel
UniMyra is offline   Reply With Quote
Old 2018-07-15, 06:31 PM   #30
LargeEddie
Measure once, trim to fit
 
LargeEddie's Avatar
 
Join Date: Apr 2013
Location: Greensboro, NC
Age: 57
Posts: 1,478
Quote:
Originally Posted by UniMyra View Post
Should I get new spokes, or will the old ones be ok?
I would go with new ones if money wasn't too tight. Spokes very often (most often?) break because of metal fatigue, and putting in fresh ones now while you're unlacing and re-lacing the wheel gets you a fresh start. You can save a few shekels by reusing them but it's much easier to replace them now than it will be later.

It's also a chance to upgrade to a better spoke if you think there's something to be gained there. (E.g., double-butted spokes are not only lighter but the extra spring from thinner middle part is said to reduce reversing loads at the vulnerable ends where they tend to break over time.)
LargeEddie is offline   Reply With Quote
Reply

Tags
book, experience, novice, read, wheelbuilding


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Wildside MTB 4 Day Epic Race in Tasmania, Jan. 2014...Who want's to join me?! unicycle6869 General Unicycling Discussions 17 2013-06-18 11:47 PM
wheelbuilding e-book ezas General Unicycling Discussions 11 2010-07-30 04:11 AM


All times are GMT. The time now is 01:38 PM.


Powered by vBulletin®
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Copyright © 2001-2016 Gilby
You Rated this Thread:
Page generated in 0.33192 seconds with 13 queries