Announcement

Collapse
No announcement yet.

Nimbus D-brake -vs- Mountain Uni UCM brake mounts

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • #46
    Originally posted by mowcius View Post
    You can't? I thought you just needed to use a 160mm front adaptor?
    I was getting a unicycle prepped for a trip, Shaved down a d'Brake to use it with a Schlumpf and KH cranks. I was originally going to use a 180mm disk like I usually do but both my spares seemed to have disappeared. I "borrowed" the 160mm disk from my bike and when I tried using the 160R/180F adaptor flipped there were clearance issues at the bottom. I could not find my 160F adaptor, It was probably with the disks and a few more odds and ends I seem to be missing. It fit fine on the UCM.

    I had thought that I had run a 160mm disk before so was surprised. You are probably right that I just needed the 160F adaptor.

    Between the UCM, the d'Brake, and the custom Triton frame I had I don't necessarily remember all the combinations I have tried.
    My friends, love is better than anger. Hope is better than fear. Optimism is better than despair. So let us be loving, hopeful and optimistic. And we’ll change the world. - Jack Layton

    Comment


    • #47
      Mountain uni?

      I find interesting this thread...
      [OT]
      What's mountain uni site to buy?
      Someone spoke about square cranks with disc brake... where I can buy one?!? Does exist Sinz 125mm square-cotterless crank which could fit a disc brake? Where to buy in Europe?[\OT]

      Comment


      • #48
        Mountain Uni doesn't have an active website anymore. there are some old pages here:

        http://mountainuni.blogspot.com/


        I believe Jeff, who runs it, may have some parts (UCM, Cranks, Discs) still available. I will PM you his email.

        Comment


        • #49
          Originally posted by Vogelfrei80 View Post
          Someone spoke about square cranks with disc brake...
          This may present a challenge because a square taper spindle doesn't have a hard stop for the crank. In other words each time you remove and replace the crank it may end up in a different lateral position.

          I know square taper disc brakes have been done in the past, but the lack of stop alone would sway me away from using one over an ISIS setup.
          Unicycling is the fountain of youth.

          Comment


          • #50
            Thank you!

            Thank you all for your precious help!

            Comment


            • #51
              Thanks for the help. Learned lots just by reading here.

              Comment


              • #52
                Due to strong vibrations (unicycle turned in to a giant vibrator) on braking I had to do something to enforce the d'brake, so thanks for the tips in this thread. I used patentband which was what I had lying around. It's not ideal because it is soft, but with 3 lairs and bolts to hold them together it worked well. When I fitted the d'brake to my KH36, I had to use 3 washers between the brake and the D'brake to get the brake centered over the rotor. I think this may have increased the vibrations. The patentband was exactly the same size as the washers, so I could just replace the washers with the patentband. I went for a 23 miles ride yesterday, and the braking was very smooth on the steepest decents.

                A few months ago I bought a d'brake for my KH36, but the bolts were not flush with the d'brake. The one on the bottom was too close to the spokes because it was sticking out. I replaced it with and older version of the d'brake that I had on an Oracle 24, which is the one in the photos. Vibrations was never an issue with any of my Oracles (24/26).
                Attached Files
                Last edited by UniMyra; 2018-07-01, 06:56 AM.
                UniMyra's YouTube channel

                Comment


                • #53
                  I had similar issues with bolt head sizes and the d-brake - I had to dig around in my parts box to find some that were just small enough to fit in.

                  Just a quick update on my strut - I'm now on version #4 but this one's been holding up well for a while so I've painted it to match
                  "Ride It Baby!"

                  Comment

                  Working...
                  X